This could be a retarded question. Disconnect starter wiring harness and remove old starter. The 6 gauge alternator output wire is good for up to 100 amps, use a 4 ga for up to 150. I'm trying to hook the original ignition switch up on my car. I was having problems with my starter, so when i went to remove it i realized it was just old brittle wiring was the issue.
I just googled chevy mini starter instructions and found some .
The picture below is identical to my setup except i have a extra wire . When i took the engine out of my truck i was in a real hurry and did not pay attention to the wires i took off of the starter. I just googled chevy mini starter instructions and found some . This could be a retarded question. But i did notice that my starter wiring has an extra wire on the pos bolt. I was having problems with my starter, so when i went to remove it i realized it was just old brittle wiring was the issue. Disconnect starter wiring harness and remove old starter. Okay, on the wire harness in the engine compartment, the one that is used for ignition, starter, etc.my . Use this diagram for wiring the starter to prevent starter solenoid contact welding for high torque competition engine . I did search, didn't find what i needed. The 6 gauge alternator output wire is good for up to 100 amps, use a 4 ga for up to 150. I'm trying to hook the original ignition switch up on my car. I am trying to wire up my starter for my sbc, .
Hold new starter motor in position at engine block. The picture below is identical to my setup except i have a extra wire . This could be a retarded question. I did search, didn't find what i needed. I am trying to wire up my starter for my sbc, .
I'm trying to hook the original ignition switch up on my car.
Okay, on the wire harness in the engine compartment, the one that is used for ignition, starter, etc.my . I just googled chevy mini starter instructions and found some . When i took the engine out of my truck i was in a real hurry and did not pay attention to the wires i took off of the starter. I was having problems with my starter, so when i went to remove it i realized it was just old brittle wiring was the issue. Use this diagram for wiring the starter to prevent starter solenoid contact welding for high torque competition engine . I did search, didn't find what i needed. Hold new starter motor in position at engine block. But i did notice that my starter wiring has an extra wire on the pos bolt. The picture below is identical to my setup except i have a extra wire . I am trying to wire up my starter for my sbc, . This could be a retarded question. I'm trying to hook the original ignition switch up on my car. The 6 gauge alternator output wire is good for up to 100 amps, use a 4 ga for up to 150.
Okay, on the wire harness in the engine compartment, the one that is used for ignition, starter, etc.my . I was having problems with my starter, so when i went to remove it i realized it was just old brittle wiring was the issue. The 6 gauge alternator output wire is good for up to 100 amps, use a 4 ga for up to 150. Hold new starter motor in position at engine block. When i took the engine out of my truck i was in a real hurry and did not pay attention to the wires i took off of the starter.
Hold new starter motor in position at engine block.
The 6 gauge alternator output wire is good for up to 100 amps, use a 4 ga for up to 150. I did search, didn't find what i needed. Okay, on the wire harness in the engine compartment, the one that is used for ignition, starter, etc.my . Hold new starter motor in position at engine block. Disconnect starter wiring harness and remove old starter. I am trying to wire up my starter for my sbc, . I was having problems with my starter, so when i went to remove it i realized it was just old brittle wiring was the issue. I just googled chevy mini starter instructions and found some . I'm trying to hook the original ignition switch up on my car. Use this diagram for wiring the starter to prevent starter solenoid contact welding for high torque competition engine . The picture below is identical to my setup except i have a extra wire . But i did notice that my starter wiring has an extra wire on the pos bolt. This could be a retarded question.
Sbc Starter Wiring / 1 -. But i did notice that my starter wiring has an extra wire on the pos bolt. When i took the engine out of my truck i was in a real hurry and did not pay attention to the wires i took off of the starter. Use this diagram for wiring the starter to prevent starter solenoid contact welding for high torque competition engine . I just googled chevy mini starter instructions and found some . Hold new starter motor in position at engine block.
Tidak ada komentar:
Posting Komentar